Thursday, April 28, 2016

MPO Cables Testing Method

As the migration to 40G/100G Ethernet using parallel array transmission systems, the high-density MPO cables are widely used in the data center. In the connection, contamination even as small as 0.001 mm can cause the optical loss. Mating a contaminated connector to a clean connector will lead to poor performance and can damage the connection. So it’s important to test the link segments consisting of MPO array cabling and keep the cable clean. However, MPO cable testing and cleaning is full of challenges.
Why MPO cables testing and cleaning is not easy? First, MPO connectors are very sensitive to dirt and contamination. The ferrules are large and hard to clean and inspect. Most microscopes don’t have adapters for MPO connectors. Those microscopes with adapters for MPO connectors can only see a small section of the ferrule because they are adapted from single fiber microscopes. So you have to inspect the entire ferrule and every fiber. Second, cleaning is also a problem because of the designs of MPO connectors with pins and holes. Most dry cleaners can only clean the place between the pins. So dirt may increase around the pins or in the holes, which cause alignment problems. So remember often keep MPO connectors well covered and protected when not in use.
Calculate the Acceptable Attenuation
Calculate the acceptable total loss of the entire optical link so that you can find if the test result is good or bad. Do as the following steps with your link loss calculator:
  • 1. Select the fiber type and test wavelength combination;
  • 2. Select the unit of length in feet or meters;
  • 3. Enter the total link length under test;
  • 4. Enter the number of connections of each type (a pair of connectors counts as one connection);
  • 5. Enter the number of splices (each connection counts as a connection plus a splice).
MPO Trunk Cable Testing Procedures
In this case, MPO connectors can be directly connect to the test equipment. That requires 12 output sources and either 12 input ports or an MPO port with a detector which can accept the light from 12 or 24 fibers. But at present this is not available. In the laboratory or factory settings, there are test equipment that can achieve this. Then, engineers use an MPO to LC fan-out cord to separate the trunk into single fiber channels for testing.
There are five basic steps for an MPO trunk cable testing (see figure 1):
MPO testing
Figure 1. set reference (three pictures above) and test MPO cable (two pictures below)
  • 1. Find a test equipment where the input port can be changed to an LC or has an LC already.
  • 2. Set a reference and there are three methods. Insert the known good cords into relative input ports and run an autotest (the above three pictures). If the loss is fewer than 0.1 dB (usually the maximum loss of LC connection is 0.2 dB), then the reference cords are good. This is critical to the test.
Reference MethodReference CableConnectors Included in MeasurementEstimated Reduction in Measured LossEstimated Increase in Errors
1-Cable Method(test equipment compatible with connectors being tested)1, launch00 dB0 dB
2-Cable Method(single fiber ferrule connectors, test equipment not compatible with connectors being tested)2, launch and receive10.2-1 dB+/-0.2 dB
3-Cable Method(male/female or plug and jack connectors, test equipment compatible with connectors being tested)3, launch, receive and “golden cable”20.3-1.5 dB+/-0.25 dB

  • 3. After setting the reference, remove the middle test reference cords and connect fan-out cables with an MPO trunk cable.
  • 4. Measure and record the loss every pair of LC connectors at the left side.
  • 5. Measure and record the loss every pair of LC connectors at the right side.
Summary
Compare the test result with calculated acceptable attenuation, If the test result is not ideal,that may be caused by the contamination, defects in the cable plant, or improper test equipment usage. Then you should better check connector end-faces for dirt and defects, and check link segment for broken fiber, poor splices and tight bends. MPO connectors are very likely to be contaminated because of fibers, number of connections and tight loss budgets. To keep MPO cabling system perform well, frequent cleaning and inspection with one-click cleaner are required.
Originally published at www.fiber-optic-equipment.com

Friday, April 22, 2016

How to Choose a Right XFP Transceiver Module?

Optical transceiver module plays an important role in optical communication network. Why is it called transceiver? A transceiver has both transmitter and receiver which are combined to form a unit and use the same channels. So word “transceiver” takes “trans” from “transmitter” and “ceiver” from “receiver”. And that’ the device with functions of transmitting and receiving.
Optical transceivers have many types, including SFP, GBIC, XFP, SFP+, CFP, QSFP+, etc. They are most often used in computers, telephones and radios. In its simplest sense, a transceiver is widely used for computer networking purposes. Whenever you discuss networking, you immediately come to think of neighborhood networks and Ethernet standards. But some types of Ethernet networks require the utilization of specific types of transceivers in order to work.
Maybe you will not face the issue about buying optical transceivers by yourself. But what if one day you came across this problem. For example, if you are going to buy 10G XFP transceivers, you must know about something to get transceivers at very reasonable rates prior to making your decision. So you are suggested to know the tips of how to choose the right transceiver for you or your friend connection nearby or at office.
xfp transceiver
XFP transceiver is a hot pluggable component for high speed computer network and telecommunication links that use optical fiber. It can be applied in the application of 10 Gigabit Ethernet and DWDM fiber optic networks. XFP transceiver is a protocol autonomous optical translation device. The main feature of XFP transceiver is that it can support 9.95Gb/s to 11.1 Gb/s data rate, transmission distance up to 80 km and operating temperature range is 0°C~70°C. Today, many kinds of XFP transceivers are available in the market, such as 10GBASE-LR XFP, 10GBASE-ER XFP, 10GBASE-SR XFP, 10GBASE-ZR XFP. See how far each XFP transceiver can support.
10GBASE-LR XFP: the maximum distance is 10 kilometers over 1310 SMF;
10GBASE-ER XFP: the maximum distance is 40 kilometers over 1310 SMF;
10GBASE-ZR XFP: the maximum distance is 80 kilometers over 1310 SMF;
The most popular and widely used is 10GBASE-SR XFP which has a working distance of 300 meters maximum via OM3 MMF.
Since the development of internet shopping, you can buy a transceiver from local store or from the internet. But the question is how to make sure that you can buy a high quality transceiver as there are so many online shops? Two most widely used and reliable brands of transceivers are Cisco and Juniper. Before making your decision, try to read the reviews on the web and testimonials from people who have used these brands. That will help a lot.
However, the brands are too expensive. There are various companies who develop 10G XFP transceivers. And those are called the third party transceivers. So maybe you can choose compatible brands which have the same functions and ideal compatibility ideal for Cisco, Juniper, Finisar, etc.. These XFP transceivers are also developed on the basis of international industrial standards and are severely checked for compatibility with tools and devices from large organizations in industry. The most important is that the price of compatible XFP transceivers is extremely low!
Fiberstore (FS.COM) is one of the companies which have cost-effective XFP transceivers. We provide 10GBASE-LR XFP, 10GBASE-ER XFP, 10GBASE-SR XFP, 10GBASE-ZR XFP, Bidi XFP, CWDM XFP, DWDM XFP. All XFP transceivers have gone through quality assurance test program to realize full compatibility. Compatible brands include Cisco, Juniper, Finisar, Brocade, HP, Netgear, etc.. For more information, please visit the site www.fs.com and contact us via sales@fs.com.
Originally published at www.fiber-optic-equipment.com

Tuesday, April 12, 2016

How Does Fiber Optic Loss Occur?

Data transmission through fiber optic cable has many advantages over other transmission media such as copper cable or radio. Compared with other transmission media, fiber optic cable is lighter, smaller and more flexible with faster speed over long distance. However, there are some factors influencing the performance of fiber optic cable. Fiber optic loss is an important factor to be considered when selecting and installing cables. This article will introduce detailed information about fiber optic loss.
When a beam of light carrying signals travels through the core of fiber optic cable, the light will become weaker. That means the signals will be weaker. This phenomenon is called fiber optic loss or attenuation. The decrease in power level is described in dB. To transmit optical signals smoothly and safely, fiber optic loss must be decreased. Fiber optic loss is caused by internal reasons and external causes, which are also known as intrinsic fiber core attenuation and extrinsic fiber attenuation.
loss-in-fiber-optic
Intrinsic Fiber Core Attenuation
Internal fiber optic loss, also usually called intrinsic attenuation, is caused by the fiber optic cable itself. There are two causes of intrinsic attenuation. One is light absorption and the other one is scattering.
Light absorption is a major reason of fiber optic loss during optical transmission. Light is absorbed in the fiber by the materials of fiber optic cable. So light absorption is also known as material absorption. The lost power actually transferred into other forms of energy like heat because of molecular resonance and wavelength impurities. Atomic structure lies in any pure material and they absorb selective wavelengths of radiation. More over, we can’t find total pure materials in the market. So manufacturers use germanium and other materials with pure silica to optimize the fiber optic core performance.
The scattering of light is caused by molecular level irregularities in the glass structure. The light scatters in all direction. Some of them keeps traveling in the forward direction. And the light not scattered in the forward direction will be lost in the fiber optic link. Thus, to reduce fiber optic loss caused by scattering, the fiber optic core should be almost perfect and the fiber optic coating and extrusion should be carefully controlled.
Extrinsic Fiber Attenuation
Extrinsic fiber attenuation is also an important factor influencing the performance of fiber optic cable. It’s usually caused by improper handling of fiber optic cable including bend loss and splicing loss.
Bend loss is generally caused by fiber optic bend. There are two kinds of bending: micro bending and macro bending. Macro bending refers to a large bend in the fiber (with more than a 2 mm radius). To reduce fiber optic loss, you should better notice the followings:
  • Fiber core deviate from the axis;
  • Manufacturing defects;
  • Mechanical constraints during the fiber laying process;
  • Environmental variations like the change of temperature, humidity or pressure.
bend-loss
Fiber optic splicing is another cause of extrinsic fiber attenuation. It’s very common to splice fiber optic cable. So the splicing loss can’t be avoided but can be reduced with proper handling ways. For example, you can choose high quality fiber optic connectors and fusion splicing machine.
There are many factors causing fiber optic loss. To reduce the intrinsic fiber core attenuation, you should select good quality fiber optic cable. To reduce extrinsic fiber attenuation, you should better need proper handling and skills.
Originally published at www.fiber-optic-equipment.com

Thursday, April 7, 2016

Maintaining MPO/MTP Polarity

The local area network (LAN) campus and building backbones as well as data center backbones are migrating to high cabled fiber counts to meet system bandwidth needs and provide the highest connectivity density. So manufacturers start to produce MPO/MTP high density cables. Then many network designers are turning to MPO/MTP trunk cable to get the highest connectivity density for an easy migration from 10G to 40/100G. To ensure reliable system performance as well as support ease of installation, maintenance and reconfiguration, MPO/MTP cables require unique polarity design. But how to maintain proper MPO/MTP polarity?
Optical fiber links typically require two fibers to make a complete circuit. Optical transceivers have a transmit side and receive side. In any installation, it is important to ensure that the optical transmitter at one end is connected to the optical receiver at the other. This matching of the transmit signal (Tx) to the receive equipment (Rx) at both ends of the fiber optic link is referred to as polarity. In traditional cabling systems, single fiber connectors such as LC, SC are used. So it’s easy to main the polarity as long as the A side of one connector pair matches to the B side of the other connector pair in any patch cord or permanent link. However, pre-terminated, high-density cabling systems based on MPO/MTP array connectivity require a new set of design rules and have their more complicated requirements for maintaining proper polarity. Before talking about maintaining MPO/MTP polarity method, we will first introduce MPO/MTP array connectors.
MPO/MTP Array Connectors
MPO/MTP array connectors terminate multiple fibers in a single high-density interface. 4-, 6-, 8-, 12-, 24-, 36- and 72-fiber connectors are available. But 12-fiber array connectors are the most common. MPO/MTP array connectors are employed in high-density permanent link installations and can be found in pre-terminated cassettes, trunk and hydra cable assemblies used extensively in data centers.
MPO/MTP array connectors are pin and socket connectors (as shown in the following picture), requiring a male side and a female side. Cassettes and hydra cable assemblies are typically manufactured with a Male (pinned) connector. Trunk cable assemblies typically support a Female (unpinned) connector. To ensure proper end-face orientation during mating process, connectors are keyed. When the key is at the bottom, it’s called key down. When the key is on the top, it’s called key up. Under the situation of key up, the fiber holes in the connector is numbered from left to right as P1, P2... There is a white dot on one side of the connector to identify where the P1 is.
mpo-mtp-connector
Three Polarity Methods
The following will introduce three different methods to maintain polarity for systems using MPO/MTP optical connectivity. Defined by TIA/EIA-568-B.1-7, these methods include installation and polarity management practices, and provide guidance in the deployment of these types of fiber array links.
Method A
Method A employs Key Up to Key Down adapters to connect the array connectors. In this straight through configuration, Fiber 1 (P1) in the near end cassette mates to Fiber 1 (P1) in the trunk cable assembly. That is to say fibers at each end of the cable have the same position. Method A provides the simplest deployment for single-mode and multimode channels, and can easily support network extensions.
Method-A
Method B
Method B uses Key Up to Key Up Adapters. The fiber circuit is completed by utilizing straight patch cords at the beginning and end of the link, and all of the array connectors are mated Key Up to Key Up. In this method, the fiber positions are reversed. Fiber 1 is mated with fiber 12, Fiber 2 mated with Fiber 11... To ensure proper transceiver operation with this configuration, one of the cassettes needs to be physically inverted internally so Fiber 12 is mated with Fiber 1 at the end of the link. This method is more complicated than method A to manage the polarity of links. As you should identify where the actual inversions need to occur. And it also requires two separate cassettes or special labeling and management of the cassettes on one end are flipped. What’s more, this method doesn’t easily accommodate angled polished (APC) single-mode connectors.
Method-B
Method C
Method C uses Key Up to Key Down Adapters. This method uses straight patch cords and the same cassettes as in Method A. The difference is that the flip does not happen in the end patch cords but in the array cable itself. for example, Fiber 1 on one end is shifted to Fiber 2 at the other end of the cable. The Fiber 2 at one end is shifted to Fiber 1 at the opposite end etc. So it’s also complicated to properly manage the polarity of the links and to identify where the actual flipped array cord is placed in the link. Besides, it’s hard to extend the links. So this method is not suitable to be applied with emerging 40Gbps standards.
Method-C
Conclusion
There are three methods to maintain MPO/MTP polarity. Network designers should evaluate each method before implementing to ensure the reliability, ease of installation, maintenance and reconfiguration as well as easy migration to higher data rates solutions like 40/100G Ethernet. It’s recommended that a method selected should better not be changed in an installation.
Originally published at www.fiber-optic-equipment.com

Wednesday, March 30, 2016

Optical Fiber Selection for Network Interconnection

The emergence of Data Centers, Storage Area Networks and other computing applications drives the needs for ultra-high speed data interconnections and structured cabling. The interconnect media choices include wireless technology, copper cable and optical fiber cable. Fiber cable offers the highest bandwidth and supports the highest data rates. There are single-mode and multimode fiber types. Different types of fiber connect with fiber optic transceivers resulting in different performances and costs. So it’s important for the network designers to understand the fiber types and select the right fiber and corresponding fiber optic transceivers for network interconnection.
Optical Fiber Types
There are three main types of optical fiber suitable for network interconnection use:
9/125μm Single-mode fiber
50/125μm multimode fiber
62.5/125μm multimode fiber
optical-fiber-types
The above numbers respectively mean the diameter of the glass core where the light travels and outside glass cladding diameter which is almost the same to most fiber types. So the difference of each fiber type is caused by the core diameter. It has great impact on system performance and system cost when balanced against network application needs. Two primary affected factors are attenuation and bandwidth.
Factors Affected by the Fiber Core Diameter
Attenuation is the reduction of signal power, or loss, as light travels through an optical fiber. Fiber attenuation is measured in decibels per kilometer (dB/km). The higher the attenuation, the higher rate of signal loss of a given fiber length. Single-mode fibers generally operate at 1310 nm (for short range) while multimode fibers operate at 850 nm or 1300 nm. Attenuation is not usually considered to be the main limiting factor in short rang transmissions. But it can cause big differences in high speed network such as 100Gb/s.
Bandwidth means the carrying capacity of fiber. For single-mode fiber, the modal dispersion can be ignored since its small core diameter. Bandwidth behavior of multimode fibers is caused by multi-modal dispersion during the light traveling along different paths in the core of the fiber. It has an influence on the system performance and data rate handling. Multimode fiber uses a graded index profile to minimize modal dispersion. This design maximizes bandwidth while maintaining larger core diameters for simplified assembly, connectivity and low cost. So manufacturers start to develop higher-performance multimode fiber systems with higher bandwidth.
System Costs: Single-mode and Multimode Fibers
A fiber optic transceiver usually consists the optical light sources, typically LED–light emitting diode and optical receivers. Since the core diameter size and primary operating wavelengths of single-mode fiber and multimode fiber are different, the associated transceiver technology and connectivity will also be different. So is the system cost.
To utilize the single-mode fibers generally for long distance applications (multi-kilometer reach), transceivers with lasers such as SFPP-10GE-LR (an SFP+ 1310nm 10 km transceiver supporting single-mode fibers) that operate at longer wavelengths with smaller spot-size and narrower spectral width. But these kinds of transceivers need higher precision alignment and tighter connector tolerance to smaller core diameters. Thus, it causes higher costs for single-mode fiber interconnections. To lower the cost, manufacturers produce transceivers based on VCSEL (vertical cavity surface emitting laser), for example, 10G-SFPP-SR (an SFP+ 850nm 300m transceiver supporting multimode fibers), which are optimized for use with multimode fibers. Transceivers applying low cost VCSEL technology to develop for 50/125μm multimode fibers, take advantage of the larger core diameter to gain high coupling efficiency and wider geometrical tolerances. OM3 and OM4 multimode fibers offer high bandwidth to support data rates from 10Mb/s to 100Gb/s.
Conclusion
Optical fiber is an easily-installed medium that is immune to electromagnetic interface and is also more efficient in terms of power consumption. What’s more, fiber optic cable can save space and cost with higher cabling density and port density over copper cabling. For single-mode fiber and multimode fiber, each one has its advantages and disadvantages. Network designers should better select the right fiber type and related fiber optic transceivers according to specific situations for higher system performance. Of course, cost is another important factor to be considered.
Originally published at www.fiber-optic-equipment.com

Tuesday, March 22, 2016

To Upgrade from 10G to 40G or not?

Some enterprises have built 10G network links. But one can never imagine how fast the network traffic is growing. There are many factors influencing the needs for high bandwidth, such as the rising populations of network subscribers, business and personal competitiveness, and the use of more video. In that way, 10G network is not able to meet the increasing needs. Then it pushes optical backbones and metro core networks to move to 40G network. However, to move to the high capacity network, many difficulties must be encountered in optical fiber networks. The question is to upgrade to 40G or not?
Difficulties of Upgrading to 40G
 
Cost Increases
The first challenge some service providers face when they consider moving to 40G technology is the cost of equipment. That’s the same when considering upgrading from 2.5G to 10G. The price of a 40G link is expensive than that of 4*10G links (as shown in Figure1). Equipment is one of the price determining factors. For example, a QSFP transceiver (the average market price of a JNP-QSFP-40G-LX4, Juniper Compatible 40GBASE-LX4 QSFP+ Transceiver, is more than US$ 2000.00) is more expensive than 4 SFP+ transceivers (the average market price of per FTLX8571D3BCL, Finisar Compatible 10GBASE-SR/SW SFP+ Transceiver, is about US$ 100.00). And some equipment may not be suitable for 40G networks, which means brand-new expensive equipment are needed.
10G-to-40G
Figure1. 10G to 40G
Optical Signal to Noise Ratio (OSNR) Drops
A unit of information, called a symbol, transmitted at 10G takes 100 pico seconds (100ps), and that symbol transmitted at 40G takes 25ps. This means the receiver translating the light back into a symbol deals with only 25% of the light of a 10G symbol. It causes 6 dB OSNR to drop. The OSNR is a measure of the strength of the signal. So the drop of 6dB means the link length will be decreased by 75%.
Chromatic Dispersion (CD) Increases
When a signal travels through a fiber, CD causes the pulses constituting the signal to spread in time. If this spreading is not compensated, these pulses will overlap. It means the signal is unusable. Comparing to 10G, this effect is 16 times more obvious at 40G. This creates a serious roadblock for 40G system operating.
Polarization Mode Dispersion (PMD) Increases
PMD is another problem which may be the most difficult to solve. This occurs due to infinitesimal imperfections in the circularity of the core of a fiber, which may be caused by the material itself, manufacturing process, or stress in the field created by bending or twisting. PMD is more capricious than predictable, and is very dependent on the qualities of the fiber. PMD can be influenced by factors including cable age or vintage, temperature of cable, cable design and cable manufacturer, etc.
Methods to Overcome Those Difficulties
To achieve 40G, new modulation schemes and approaches are being developed. The following tells about methods to overcome those difficulties.
Save Cost
We can discuss it from two sides: to buy or not to buy new equipment. First, to buy new equipment. As mentioned above, some optical equipment like transceivers from Google searching result are quite expensive. Thanks to the fast developed technology, manufacturers like Fiberstore (FS.COM) produce many compatible brands of which the price is quite low. The price of FS.COM JNP-QSFP-40G-LX4 is US$ 400.00 and FTLX8571D3BCL is US$ 16.00. Compared with the average market price, it’s obvious that FS.COM products have advantages on price. Now you may doubt that transceivers with such a low price will not have good quality. Then you don’t need to worry about it when you see FS.COM test assured program which provides world-class customer confidence in each fiber optics. Except transceiver optics module, FS.COM also has other cost-effective optical products for you to upgrade to 40G network.
Second, not to buy new equipment. Consider that many enterprises have spent a lot investments in 10G networks, many carriers would like to upgrade to 40G by just inserting new 40G cards into their existing 10G WDM systems to save cost. Here are three advisable strategies moving from 10G to 40G: Use the current fiber plant of the 10G routes, and not invest in expensive deployments of new fiber for 40G; Add 40G to currently installed equipment, so additional equipment is not required to sit alongside the 10G gear; Keep the network robustness and architecture intact, that is, the current line design, so that the numbers of OADM and ROADM nodes on any pathway in a ring or mesh do not need to be reduced.
Improve OSNR, CD, PMD
Problems related to OSNR, CD and PMD are caused by optics, the fiber quality and other optical equipment on one side. So you should better choose high quality equipment. On the other side, it depends on advanced optical technology bringing about simplified materials and better methods.
Conclusion
Although there are many challenges, the trend of upgrading from 10G to 40G is inevitable. With the above methods and more advanced fiber optical technologies, you should upgrade to 40G network without any hesitation. Besides, to help customers to achieve 40G smoothly, FS.COM researches and develops high-quality products with favorable price. And FS.COM will keep providing customers with more cost-effective equipment and better solutions to realize 40G upgrading.
Originally published at www.fiber-optic-equipment.com

Monday, March 14, 2016

What Should We Know About Cabling Before Deploying 10 Gigabit Ethernet?

Since the need for high data speed increases and the price of optical equipment becomes more affordable, many enterprises start to deploy 10 Gigabit Ethernet in their cooperate backbone, data centers to support high-bandwidth applications. But what should we know about cabling before deploying 10 Gigabit Ethernet?
Fiber Cabling Choices
Three factors should be considered for fiber cable deployment: fiber cable type, 10 Gigabit Ethernet physical interface and fiber optical transceiver module. The following tables show the standard fiber cables, physical interfaces, and transceiver modules applicable to 10 Gigabit Ethernet.
Fiber CablesMultimodeOM1 fiber (62.5/125 μm)
OM2 fiber (50/125 μm)
OM3 fiber (50/125 μm)
Single mode9/125 μm fiber
Physical Interfaces10GBase-LRMMax distance 220m
10GBase-SMax distance 300m
10GBase-LMax distance 10km
10GBase-EMax distance 40km
10GBase-ZMax distance 80km
Transceiver modulesXENPACKLarge form factor
X2Smaller than XENPACK
XFPSmaller than X2
SFP+Smallest form factor
Note: the 10 Gigabit Ethernet physical interface type should be the same on both ends of the fiber link. For example, it is OK to deploy a fiber link with one XFP-10G-MM-SR optics on the left, and one SFP-10G-SR optics on the right. However, one SFP-10G-SR optics and one SFP-10G-LRM optics can’t connect together because of different physical types.
Copper Cabling
As switching standards copper cabling standards develop, copper cabling for 10GbE is more widely used. There are three different copper cabling technologies for 10 Gigabit Ethernet. Each one has different performances and prices.
First, 10GBase-CX4 is the first 10 Gigabit Ethernet copper standard. It’s relatively economical and allows for very low latency. But the form factor is too large for high density port counts in aggregation switches.
Second, Small Form-factor Plus (SFP+) is the latest standard for optical transceivers. 10 Gb SFP+Cu direct attach cables (DAC) directly connect into an SFP+ housing. It’s the best copper solution for servers and storage devices because it has low latency, small form factor and reasonable price.
Third, 10GBase-T is a fully IEEE compliant Ethernet transport technology standard, as defined by IEEE 802.3an-2006. 10GBase-T is to run 10 Gigabit Ethernet over CAT6a and CAT7 copper cabling up to 100 meters. 10GBase-T copper twisted-pair cabling can enable the earlier 10MB, 100MB and 1GB operation. However, 10GBase-T still needs to be improved on its price, power consumption and latency.
MediaCopper cableRange (max)Average Latency
CX4Twinax15m (49ft)0.1 μs
SFP+ DACTwinax SFP+CU10m (33ft)0.1 μs
10GBase-TCAT6 RJ4530m(98ft)—50m (164ft)>1.5 μs
CAT6a RJ45100m (98ft)>1 μs
CAT7 GG45100m (98ft)>1 μs
SFP+ Direct Attach Cables
SFP+ direct attach cables integrate SFP+ compatible connectors with a copper cable into a low-latency, energy-efficient, and low-cost solution. SFP+ direct attach cables offer the smallest 10 Gigabit form factor and a small cable diameter for higher density and optimized rack space in 10 Gigabit Ethernet (GbE) uplinks and 10 Gigabit Fiber Channel SAN and NAS input/output connections. To use SFP+ direct attach cables can save you a lot compared with fiber optic solutions. And it can still provide lower latency and save up to 50% power consumption per port than other copper twisted-pair cabling systems.
sfp+ dac
SFP+ direct attach cables can also provide enhanced scalability and flexibility. The cables connect several servers or storage devices together in a single rack. Thus, it reduces the use of intermediate patch panels. And it’s easy to move racks or deploy one rack at a time since the cabling outside of the rack is limited to the main switch connection.
Fiberstore offers comprehensive cabling solutions for 10 Gigabit Ethernet, including fiber cables, copper cables, and SFP+ direct attach cables and each one has various subcategories. Before deploying 10 Gigabit Ethernet, you need to consider factors of the performance, cost, power consumption and latency and choose the most suitable cabling solution.
Originally published at www.fiber-optic-equipment.com