Tuesday, November 8, 2016

How Much Do You Know About SONET/SDH SFP+?

Before, Plesiochronous Digital Hierarchy (PDH) system was used to transport phone calls and data over the same fiber. Since phone calls and data traffic increase a lot, SONET/SDH are introduced to replace PDH system to transport the data without synchronization problems. As you can see, you always find SONET/SDH SFP+ in the market. Now, this article will give a brief analysis on SONET/SDH SFP+.


SONET/SDH Interfaces Overview
SONET (Synchronous Optical Networking) and SDH (Synchronous Digital Hierarchy) are multiplexing protocols that transfer multiple digital bit streams over optical fiber with lasers or light-emitting diodes (LEDs). SONET and SDH are widely used methods today for very high speed transmission of voice and data signals across the numerous world-wide fiber-optic networks. SONET is the standard used in the United States and Canada, and SDH in the rest of the world. The two are largely equivalent. Although the SONET standards were developed before SDH, it is considered a variation of SDH because of SDH's greater worldwide market penetration.
We often find SONET/SDH SFP transceiver like Cisco OC-3/STM-1 LR-1 SFP 1310nm 40km IND DOM. What does OC-3/STM-1 mean? OC-3c (Synchronous Transport Signal 3, concatenated) is the basic unit of SONET. Depending on the system, OC-3 is also known as STS-3 (when the signal is carried electrically). STM-1 (Synchronous Transport Module, level 1) is the basic unit of framing in SDH, which operates 155.52 Mbit/s. OC-3c and STM-1 have the same high-level functionality, frame size, and bit-rate.
    SONET/SDH Data Rates
 
SONET/SDH and 10 Gigabit Ethernet
10 Gigabit Ethernet (10GbE) means the Ethernet network runs at 10 Gigabit per second. The 10 Gigabit Ethernet defines two PHY (Physical Layer) types: a local area variant (LAN PHY) with a line rate of 10.3125 Gbit/s, and a wide area variant (WAN PHY) with the same line rate as OC-192/STM-64 (9,953,280 Kbit/s).
10GbE provided the potential for an Ethernet solution aligned with the data rate of OC-192 backbone. It’s the first time in Ethernet history that no additional speed matching equipment would be required to link with the WAN. A seamless end-to-end Ethernet network can be built with less money. But the question is how to balance the compatibility with the installed base of OC-192 equipment while still meeting the economic feasibility criteria of the P802.3ae Task Force in defining the 10GE WAN PHY. To solve this problem, an OC-192 frame format is provided to support only the SONET overhead features required for fault isolation. This simplification avoids unnecessary functions and cost.
In order to make sure that WAN PHY optics would benefit from the high volumes and low cost of Ethernet, the serial 1310 nm and 1550 nm transceiver modules were kept the same as the LAN PHY. Since the 1310 nm and 1550 nm transceiver modules are designed for up to 10km and 40 km links respectively, they will inter-operate with OC-192 transceiver modules for 1310 nm and 1550 nm over intermediate reach, respectively.
FS.COM SONET/SDH SFP+
Fiberstore offers OC-192/STM-64 SFP+ for short reach (SR-1, VSR) , intermediate reach (IR-2) and long reach (LR-2) applications (as shown in the following table). These SFP+ modules are compatible with the SONET/SDH and ATM standards. For more details, please visit www.fs.com or contact us via sales@fs.com.
Part No.DescriptionShop Now
29932OC-192/STM-64 SFP+ 1310nm 220m DOM TransceiverBuy
29915OC-192/STM-64 VSR and 10GBASE-SR/SW SFP+ 850nm 300m DOM TransceiverBuy
29933OC-192/STM-64 SR-1 SFP+ 1310nm 2km DOM TransceiverBuy
29935OC-192/STM-64 SR-1 and 10GBASE-LR/LW SFP+ 1310nm 10km DOM TransceiverBuy
29934OC-192/STM-64 SFP+ 1310nm 20km DOM TransceiverBuy
29936OC-192/STM-64 SFP+ 1310nm 40km DOM TransceiverBuy
29939OC-192/STM-64 IR-2 and 10GBASE-ER/EW SFP+ 1550nm 40km DOM TransceiverBuy
29940OC-192/STM-64 LR-2 and 10GBASE-ZR/ZW SFP+ 1550nm 80km DOM TransceiverBuy
Originally published at www.fiber-optic-equipment.com

No comments:

Post a Comment