Things You Should Know About Patch Panel Cabinet

Cables are in the right position. Patch panels are terminated. All slack cables are put orderly in the cable manager. Let’s see what is missing? Well, where should the patch panels and cable managers be? Just lying on the ground? If indeed, the previous efforts for cable management is wasted. Just with a cabinet or a server rack, you can solve the problem. There are thousands of cabinet for different use, but here we refer to the network patch panel cabinet.

Network Patch Panel Cabinets Introduction

We have wall mount cabinets that has the maximum height of 12U and the normal cabinets standing on the ground that can reach to 45U. Unlike the open frame rack which consists of two or four mounting rails (called posts) without sides or doors, the wall mount cabinet is enclosed by SPCC cold roll steel panels and a glass front door to make its inside visible. The side panels can be removed easily for quick access to equipment and cabling. On the top of the patch panel cabinet, there is a cooling vent to ensure smooth airflow, preventing over-heat in it to further protect equipment. It is designed to house the 19-inch standard that is consistent with most patch panels in FS.COM or non-standard network equipment as well as network accessories. The wall mount cabinet is shipped fully assembled and is ready to mount to the wall.

As for the floor-standing network patch panel cabinet, the ventilation can be naturally achieved as the front door is perforated and the top panel is attached with brush guards to prevent over-heating. It has four casters helping with its move. Top, bottom and back cable access openings provide convenient and multiple cable routing choices to and from the patch panel cabinet.

Layout Inside the Patch Panel Cabinet

We all know that all patch panel are put in the cabinet, be it fiber optic patch panel or Ethernet patch panel. However, the question is whether it is on the front side or back and with the jacks facing in or out?

In most cases, we will start with an empty patch panel cabinet, and then install the devices on its front rails from top to the bottle. First comes the cable manager 1, then follows the patch panel 1, cable manager 2, switch 1, cable manager 3 and switch 2, with all the connectors on the back side of the patch panel cabinet. All gadgets ready, we can go on with the cabling. The patch panel here can be fiber or copper patch panel.

The importance of a patch panel cabinet is no less than that of a tiny screw or a nail. And great attention should be focused on it since the patch panel cabinet can support the other device and prevent them from external damages. A solid and durable patch panel cabinet is necessary, which is actually what FS.COM aims at. There are 9U and 12U, two choices for you to meet different application. To ensure the best performance, 1 bag of nuts and bolts, 1 T-Shaped Lever will be offered for free. And there are so many surprises in the patch panel cabinet that I want to leave it for you to find yourselves. You will find them when installing and using the patch panel cabinet from FS.COM.

Collections of Cable Manager for Rack

Introduction

Long before the born of cable manager, the mess cable management with cables hanging here and there has been a cloud over the data center and server room. How can you realize each smooth and convenient operation on your network application with network cables looking like messy spaghetti? Here we list four common cable managers to simplify your cabling and minimize the trouble during operation.

Different Types of Cable Manager

The following cable managers which you may have heard of or seen before are the most popular types in the market. Each has its unique design and characteristics.

Cable Manager with Brush Strip

The panel is designed to be mounted on any 19in EIA style rack or cabinet and features built-in brush that allows passage of up to 25 cables while blocking airflow, ensuring optimal thermal performance. The steel construction provides durability, resists corrosion, and keeps your rack looking smooth and professional.

Cable Manager with Finger Duct

The FS.COM finger duct horizontal cable manager is designed with flexible fingers, rear pass-through holes and a removable cover. The soft and durable finger ducts offer proper bend radius and flexible operation of cable management, keeping the structured cabling system unhurt and totally functional.

Cable Manager with D-rings

The name of D-rings cable manager originates from the fact that five metal D-rings stand vertically on the cable management panel in a good order. Horizontal cable management panels with D Rings are built with steel for strength and durability. Easily route large amounts of cable through robust rings. The D-Rings organize patch cords and maintain a required bend radius. They are available in sizes of 1U and 2U.

Cable Manager with Bend Radius Finger

This cable manager is equipped with six or five bend radius control fingers, consuming much fewer material. The total length of it is 222mm. Light in weight, this type of bracket can be installed in specific areas of the rack, rather than along its entire height. Moreover, it can be stacked to reach any height(U), so it can be an alternative of higher vertical cable management.

How to Apply Cable Manager

Cable managers often come together with patch panel to make the patch cables in the front side of patch panel more orderly. Generally, in a server rack, the cable can’t either be put solely on cable manager since it is incompetent for termination, or be applied to just a patch panel due to its imperfect cable management. Therefore, to realize the perfect cable management, we need to deploy this couple at the same time. The cables going out from the patch panel have already gone through the management process, but it should go to the next cable manager installed above or below the patch panel, so that the whole cable management can be finished. Additionally, some people will need the further step to bring the cables that are from horizontal cable management to the vertical cable managers standing at the both sides of the cabinet.

Conclusion

Never look down upon cable management, otherwise the cables haphazardly thrown around will be your nightmare. In case it damages the wires and cause other hazards, now it’s time to arrange your cables properly. FS.COM has many kinds of cable managers to help make your life neater!

Ethernet Patch Panel Still Shining on the Market

The patch panel, a significant element in cabling design, has many ports on it. Through these ports, the cables are located elsewhere in your building. Patch panel at present has fiber and copper patch panel(also known as Ethernet patch panel), two choices for us. As we all know, a single fiber optic patch panel is not available to all kinds of fiber cables. The same is to copper patch panels which are classified as Cat5e patch panel, Cat6 patch panel and so on.

CAT5e Ethernet Patch Panel VS. CAT6 Ethernet Patch Panel

Both as the copper patch panel, Cat5e patch panel and Cat6 patch panel don’t have many differences, except that Cat5e patch panel usually works with Cat5e, while Cat6 patch panel can work with both the corresponding Cat6 cable and any earlier generation of Cat cable. The patch panels themselves don’t have many practical differences. However, there is indeed a difference in the wire gauge specified between Cat5e and Cat6. The cat6 wire is thicker in that Cat6 usually has 23 AWG copper conductors compared to only 24 AWG in Cat5e cable.

The 24 port patch panel used for different cables are both welcomed by customers. 24 port cat6 patch panel offered by FS.COM acquires acknowledgments from many customers and IT experts. With easy installation and top-quality performance, the high quality patch panel is designed for Fast Ethernet applications. 24-port Cat5e patch panel is the most popular in the market, which has punch down and feed-through patch panel for customer choice. And when applying patch panels to special environments, for example nearby motors, generators, air conditioners, and even office mainstays such as fluorescent lights and printers, you should carefully consider between shielded and unshielded patch panels.

Shielded Ethernet Patch Panel VS. Unshieleded Ethernet Patch Panel

Shielded and unshielded patch panels are required to match with the shielded and unshielded copper cable applications. Shielded patch panels are designed for high EMI (Electro Magnetic Interference) environments. If the application environments have special requirements for crosstalk and EMI functions, especially when the copper cable runs near power cables then you should choose to use shielded Ethernet cables with shielded patch panels. However, someone may wonder whether they can use unshielded patch panel for shielded cable. To be honest, it depends on the environment in which your cable will run through. If the place has no high power electrical wires, you can go with unshielded patch panel. On the flip side, if you are in a noisy environment like using arc welders or near high power radio transmitters, then you’d better select the shielded one. FS.COM shielded and unshielded patch panels can meet not only 1G network speed, but also 10G network.

For both shielded and unshielded applications, you can find what you need at FS.COM. The port number marked on the FS.COM patch panel provides easy cable identification. The cable manager on the rear side is removable, providing efficient and organized cabling.

Conclusion

CAT5e and CAT6 cables are the most popular Ethernet cables on the market. To create a nicely organized cabling environment, choosing the right patch panel is essential. Sometimes Cat5e, Cat6 or other Ethernet cables need to be managed in a single panel, in this type of situation, the blank keystone patch panels can support mixed cabling with installation of different rj45 insert modules. In addition, you can customize your patch panel according to your specific applications. FS.COM provides a large variety of patch panels and Ethernet cable and also presents a selection of cable managers to help you create your ideal cabling network. For more details, please visit our website.

D-Ring Cable Manager for Horizontal Cable Management

The horizontal cable management solutions are springing up one after another as is expected. After the the explanation of versatile fiber optic patch panel, punch down patch panel, upgraded fiber enclosure, and various cable managers such as brush strip cable manager, finger duct cable manager, horizontal and vertical manager, we now focus our eyes on the new horizontal cable manager with D-rings.

The Structure of D-ring Horizontal Cable Management Tool

The name “D-ring” stems from its design that a ring goes in “D” frame. The five metal D-rings stand vertically on the cable management panel in a good order. Without complicated design, it won’t add unnecessary trouble in the cabling procedure or additional energy for you to identify each gadgets. For 1U cable management, we have 1U horizontal cable management with D-rings, and 2U horizontal cable manager with D-rings for 2U cable management.

The Advantage of D-ring Horizontal Cable Management Tool

Why is the D-ring horizontal cable manager standing out among all those cable managers? Why you want choose it? Look here.

For those who want neat and clean cable management, it perfectly caters to their need as it uses a D-ring method of cable management to run cables vertically along the side of your rack, neatly guiding them between equipment that’s mounted at different heights. This provides a tidy and well-organized way to run cables from devices mounted toward the bottom of your rack to other devices mounted near the top, without leaving a mess of cables hanging in between.

For those who long for easy installation and effortless maintenance, this D-ring cable manager can satisfy them because having neatly organized and routed cables not only improves the appearance and accessibility of your rack, it also makes it easier for you to install, access and maintain rack components. As a consequence, we can see that it improves the appearance and accessibility of your rack. That’s why we want to have it.

How to Arrange Horizontal Cable Management with D-ring Cable Manager

The user-friendly design makes it easy to use by customers and even novices. With screws and installing tools, you can attach this device onto server rack or cabinet. In the video, the cable managers are sitting below the switch. When the fiber cables on the switch are all on their position, we can now come to the cable management step. The first 4 fiber cables pass through the first ring and go through the second ring together with another 4 cables and so on. A single horizontal cable manager with D-rings can manage up to 70 patch cables. Here if you use cable ties to strap the cable, it will be the icing on the cake.

If you keep wondering where your power cords and video cables go in your 24 port patch panel, then our horizontal cable management panel with metal D-rings to provide stability so each cable can make a clean entry and exit. Make your patch panel look organized and professional. FS.COM horizontal cable management solutions provide data center managers and IT professionals with a variety of options.